Rokonet ORBiT-14 Bedienungsanleitung Seite 27
- Seite / 70
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Installation and Programming Manual
27
P
P
r
r
e
e
p
p
a
a
r
r
i
i
n
n
g
g
Y
Y
o
o
u
u
r
r
O
O
R
R
B
B
I
I
T
T
-
-
P
P
r
r
o
o
f
f
o
o
r
r
I
I
n
n
s
s
t
t
a
a
l
l
l
l
e
e
r
r
P
P
r
r
o
o
g
g
r
r
a
a
m
m
m
m
i
i
n
n
g
g
There are three “Getting Started” options when learning how to program your ORBIT-Pro.
OPTION 1: You wish to program a new ORBIT-Pro for the first time.
OPTION 2: You wish to restore all factory defaults to an already-programmed ORBIT-Pro.
OPTION 3: You wish to modify the configuration of an existing ORBIT-Pro. For this, proceed
directly to one of the following pages:
Description and Use of the LCD Keypad page 30
Installer Programming Tutorial page 35
Actual Programming page 39
For Options 1 and 2
A. Preparing the LCD Keypad:
1- Remove all Power from Your ORBIT-Pro
a) If your ORBIT-Pro has NOT been wired to an LCD Keypad, remove all power (AC and Standby
Battery) if present, and skip to Step 2.
b) If your ORBIT-Pro and at least one LCD Keypad have already been physically installed and/or wired
together, remove all power (AC and Standby Battery) if present, and skip to Step 3.
2- Wire a single LCD Keypad to the ORBIT-Pro’s Main Board
a) If required, add additional wiring to the keypad, by using no more than 1000 feet of the appropriate
wire.
3- If necessary, check the LCD Keypad’s Physical I.D. Number
If the LCD Keypad(s) have already been given an I.D. number, skip to Step 5. Otherwise, separate the
keypad’s cover from its base, locate the bank of four DIP switches and make sure the keypad is given the
I.D. of “01”, by verifying that all four switches are in the down (OFF) position
4- Reassemble the Keypad
Carefully replace the keypad’s printed circuit board in its cover housing
join the unit’s cover and base by first hooking the tops together and then snapping the bottoms in place
5- Setting the Keypad’s Tamper Switch
If the keypad is not yet mounted, locate its rear-mounted tamper “plunger” and set its action as follows:
a) if, during programming, the keypad is to be wall-mounted, be sure the slot in the plunger is vertically-
oriented, and reinstall the keypad
b) otherwise, for bench, table-top, or “hand-held” programming, turn the plunger so that its slot is
horizontally-oriented
B. Preparing the Panel: (refer to Figure 2-7 on page 25)
6- Check the Condition of the ORBIT-Pro’s J2 (DEFAULT) Jumper
Option 1: If you are Programming a New ORBIT-Pro:
a) Be sure the jumper is NOT placed over its corresponding pins. You may wish to place it on one of the
pins for safekeeping.
b) Proceed to Step 7.
Option 2: If you are Restoring Factory Defaults to an ORBIT-Pro:
a) Place the jumper in the DEFAULT position so it covers BOTH of the corresponding pins.
b) Proceed to Step 7.
7- Apply Power to the System
Do so by plugging in the AC transformer, and/or connecting the Standby Battery to the RED and BLACK
flying leads. After a moment, the keypad will display:
ROKONET
Please Wait ...
- Main Board 1
- Zone Expansion 1
- Wireless Expansion 2
- Partitions 2
- Self Monitoring 5
- False Alarm Reduction 5
- Synoptic Map 5
- Figure 1-2 6
- Power Supply Expansion Module 10
- Event Log Expansion Module 10
- Printer Module 10
- X-10 Transmitter Module 10
- Total Auxiliary 18
- Maximum Current 18
- Draw per Branch 18
- Figure 2-1 19
- Figure 2-2 20
- Figure 2-3 21
- Zone Terminations 22
- Figure 2-5 23
- Figure 2-6 24
- Wiring Diagram 25
- PROGRAMMING METHODS 26
- Table 3-1 26
- * Not for UL Installations 26
- For Options 1 and 2 27
- 7- Apply Power to the System 27
- ↓↓ 28
- Figure 3-1: The LCD Keypad 30
- INSTALLER PROG: 33
- 1)SYSTEM ↓↓ 33
- IMPORTANT: 37
- (on pages 40 through 112) 39
- 1) System 40
- INSTALL PROG: 40
- SYSTEM: TIME DEFINE (cont’d) 41
- SYSTEM: SYSTEM CONTROL 42
- SYSTEM: SYSTEM LABEL 46
- SYSTEM LABELS: 46
- 1)PARTITION 1 46
- SYSTEM: SERVICE INFORMATION 47
- 2)ZONES ↓↓ 48
- ZONES: ZONE TYPE (cont’d) 51
- ZONES: ZONE SOUND 53
- Loop 54
- Response 54
- 2)SYSTEM ↓↓ 58
- Bell Follow 63
- No Telephone Line 63
- Communication 63
- Trouble Follow 63
- Ground Pulse 64
- Low Battery Follow 64
- AC Loss Follow 64
- Sensors Test 64
- UTILITY OUTPUT: PARTITION 65
- P=12345678 UO=xx 65
- Y 65
- 3) UO ↓↓ 66
- UTILITY OUTPUT: ZONE 67
- UTILITY OUTPUT: CODE 68
- UTILITY OUTPUT (cont’d) 69
- 4) Code Maintenance 70
Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Rokonet ORBiT-14
(8 Seiten)
(31 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.065 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern